If you’ve been searching for a solution to a garage door problem, you have probably come across some common ones. Misaligned tracks, broken cables, and unplugged motors are some common ones. If you’re unsure of the cause, read on to learn more. A broken door sensor is another common issue. Here’s what you should do in case.

Misaligned tracks

When your garage door has stopped working, it may be due to misaligned tracks. As a result, they can become dented, dirty, or lack lubrication. To resolve this issue, contact a professional such as the Overhead Door Company of Puget Sound – Garage Door Repair to inspect your garage door. It may be simple lubricating rollers.

One of the most common causes of garage door problems is misaligned tracks. Even if your garage door is new, it will eventually wear down or become misaligned. You can prevent misaligned tracks by regularly cleaning and maintaining them. However, over time, grit will build up in the tracks and control the rollers and cables from working correctly. As a result, your garage door will become challenging to operate and may even need repair.

Unplugged motor

If your automatic garage door switch is not working, the problem could be a simple unplugged motor. The motor is attached to a light near the ceiling at the end of the garage door chain. Plug the engine into the socket on the garage door opener and test it. If the door works properly, it should be able to detect the photo-eye sensors. The following are some common garage door problems that you may encounter.

The controller wires for your garage opener are similar to those in your stereo. Make sure to tighten them before you attempt to move the door. Another sign that your chain is too tight is black crumbs. Finally, you must allow a little slack in the chain to prevent a clanging noise. In any case, you must call professionals in garage door repairs to check the wiring. If these two common garage door problems are causing the problem, it’s likely a malfunctioning outlet or circuit breaker.

Loose hardware

In addition to the rattling noise, a garage door can also be prone to pops and noises when the hardware is loose. Again, changing these parts may be dangerous. If unsure what to check for, you can check the garage door’s torsion springs. If these components are not loose, lubrication may be needed. In some cases, a broken antenna can cause these issues.

The tension on these cables can be uneven, causing the door to drop rapidly. If you notice uneven pressure, you should consider getting a universal aluminum retainer to fix the problem. Even if the door is closed most of the time, this may cause the cables to loosen and break. If you suspect your cables are loose, contact a garage door repair specialist immediately. Loose hardware can also lead to wobbling or grinding sounds.

Broken cables

Among the most common problems associated with garage doors are broken cables. These cables run over a system of pulleys, drums, and spools to lift and lower the door. Cables can become worn or deteriorate due to moisture near the door’s bottom or faulty pulley bearings. Additionally, out-of-adjustment garage doors can cause cables to rub on other parts of the door, increasing the likelihood of failure. Luckily, some ways to spot broken cables before they become a problem.

The most common cause of a broken cable is rubbing against another metal object. Over time, cables can weaken due to heavy contact with water or salt and become prone to corrosion. Broken cables can be a warning sign of more significant problems with your door. You should immediately call a professional garage door repair service in such cases. A technician will replace the cable and both cables if necessary. If it is the case, it’s best to contact a local garage door service company.

Broken safety sensors

One of the most common garage door problems is malfunctioning safety sensors. These sensors must be aligned at the same angle and direction to function properly. Unfortunately, the sensors have an LED light on the exterior of each unit that blinks when out of alignment. To fix this issue, simply tighten the brackets that hold up the safety sensor and bend it back to its original position. Then, the green LED light should come on again.

The sensors can be damaged by being hit or misaligned. They should be pointing toward each other. If the sensors don’t point at each other, try adjusting the wires until they are steady. Check the wiring and safety reversing sensors for any signs of damage. It may be time for a replacement if they still don’t work. However, be sure to check your garage door opener with the remote.

Broken joints

Garage doors may be noisy or have broken joints if they have become disorganized. These issues can cause your door to run unevenly. You should never attempt to close the door with an opener if you suspect one or more of these parts are broken. To fix the problem, contact a professional maintenance specialist. Broken joints can cause the door to become unusable and need to be replaced. If you notice a popping or rattling noise, you must seek immediate repair service for the door.

Another problem associated with garage doors is a broken spring. This can cause personal injury if you are inside the garage when it opens. A broken spring may also cause the door to come off its tracks and snap, resulting in a severe accident. A broken spring may also cause the door to sag or become heavier on one side than the other.